Question 1

RESPONSIBILITY

Accepted Answer

Coating Specialist, LLC to apply products per recommendation and to meet and exceed contractual obligations

Question 2

PRODUCT

Accepted Answer

ANCHOR PAINT – A LOW VOC, HIGH SOLIDS, PENETRATING OIL/ALKYD RUST INHIBITIVE PRIMER     DATA SHEET
ANCHOR PAINT – SAF-T-GARD ll ENAMEL – 900 SERIES     DATA SHEET
FAST-CLAD DTM URETHANE – B65T854     MSDS
ZINC CLAD lll HS ORGANIC ZINC-RICH EPOXY PRIMER - B69V00100     COA 
ZINC CLAD lll HS ORGANIC ZINC-RICH EPOXY PRIMER (PART A) – B69A00100     COA
CROTHANE l PREPRIME – B65C10 – SHERWIN WILLIAMS      DATA SHEET     MSDS
SHERTHANE 2K URETHANE (PART A) – B65W151     DATA SHEETMSDS
ZINC CLAD ZINC DUST – B68D11      MSDS
MACROPOXY 646 FAST CURE EPOXY – SHERWIN WILLIAMS     INFO
COROTHANE I IRONIX B     INFO
DISCO 521 NON-FIBERED FOUNDATION COATING     MSDS
DTM WASH PRIMER – SHERWIN WILLIAMS – B71Y1     INFO
MACROPOXY 646 FAST CURE EPOXY     INFO
SHER-CRYL HPA     INFO
SHERTHANE 2K URETHANE     INFO
TNEMEC ENDURA-SHIELD SERIES 73     MSDS
TNEMEC UNI-BOND MASTIC SERIES 118     MSDS
TNEMEC UNI-BOND MASTIC ALBATROSS     MSDS
TNEMEC UNI-BOND MASTIC SERIES 118     MSDS
ZINC CLAD II PLUS INORAGNIC ZINC-RICH COATING     MSDS     COA
ZINC CLAD III HS ORAGNIC ZINC-RICH EPOXY PRIMER     MSDS

Question 3

HAZARD ANALYSIS

Accepted Answer

Proper Personal Protective Equipment (PPE); Proper Safety equipment (eye protection, ear protection, gloves, respirator, steel toed boots, properly suited with vest & hard hat (harness in lift))
 
HAZARDS:
 
Hazard Analysis form

Question 4

EQUIPMENT

Accepted Answer

Brushes
Rollers
Solvents
Graco 7900
Binks pots
Conventional guns
Mixing equipment (drills, mixing paddles, generator, extension cords)
5 gallon buckets
Rubber gloves
Spray suits

Question 5

LABOR FORCE

Accepted Answer

GROUND CREW – employees who ensure the coater/equipment have everything needed in order to execute proper application.
 
MIXING CREW – employees who mix together coatings.
 
PREP CREW – employees who sandblast and pressure wash prior to application.
 
SPRAY CREW – coaters who apply the product.

Question 6

BASIC DAILY PLAN

Accepted Answer

1.  Check that all necessary equipment and PPE for proper application PRIOR TO LEAVING FOR SITE.
 
2.  Show up on site ON TIME
 
3.  CONTACT THE SUPERVISOR of job site. Share and understand prep-work, equipment needed and application process.
 
4.  Fill out, go through and sign HAZARD ANALYSIS
 
5.  Fill in the CHECKLIST throughout the entire process (time, temperature and pictures)
 
6.  COMPLETE prep work.
 
7.  COMPLETE product application.
 
8.  REVIEW days work with supervisor and have them sign off.

Question 7

PROCEDURE

Accepted Answer

Make sure surface is properly sandblasted, pressure washed and dry.
Make sure area is secure, and the mixer, sprayer and ground crews are properly equipped (PPE) (respirator, latex gloves, safety glasses)
String out and check 7900 HOSE or Binks pot hose.
Put on and secure proper SCREEN on 7900 STINGER.
Mix 1st batch of Primer. Understand pot life of material. This is found in data sheets.
Mix 2nd finish coat. Understand pot life of material. This is found in data sheets.
Put the batch under the stinger (picture) and start pump or put material into bink’s pot bladder.
Turn on PUMP SWITCH and PRIME LINE.
Spray cleaning fluid out of lines until only primer or paint is spraying.
INSERT TIP into gun housing.
Begin and finish application process.
Remove paint or primer from under stinger and replace with bucket of xylene.
Run xylene through pump and lines.
Place tips in small cup of xylene.
Put away mixing equipment.
Roll up hose.
Clean up and make sure you have secured all waste and thrown away anything that is trash.

STEEL COATING